Pages

Friday, July 18, 2014

Purple-ish 3 Piece Tag Set





Purple-ish
3 tag forum set
written 7/18/2014

Supplies Needed:


Scrap Kit is by Devlish Dezines. You can get this kit at http://scrapsncompany.com/index.php?main_page=product_info&products_id=4765

Font of your choice. I am using Vinyl George which you can get at http://www.fontspace.com/category/emo?p=2

Plugins:
Xero Moonlight
Xero Fritillary
Lokas 3D Shadow

Lets Begin:

Open element 30 from the kit and shift+d to duplicate.
Close the original.
Resize by 80%.
Make your canvas large enough to give you some room to work with.
Using your freehand selection tool set to freehand draw around the outside of the frame area.
Open the closeup of the tube and copy and paste as a new layer.
Drag under the frame.
Position her face in the framed area and go to selections invert and hit delete.
Selections select none.
Adjust hue and saturation and set both to 0.
Apply the Xero Moonlight filter using the default settings.
Duplicate the frame layer and drag to the bottom.
Adjust blur gaussian blur at 10.
Apply Xero Fritillary at the default settings.
Merge your top frame and your tube layer together.
Resize this top layer by 90%.
Reposition over the fritillary layer so it sits centered.
Add a nice drop shadow to the top layer.
I used
0 0 100 9.00 color black
Open up your main full tube and copy and paste as a new layer.
Move to the right side of the frame.
Apply the Lokas 3D shadow using the preset flat solid shadow.
Open element 24 and resize by 50% and then again by 65%.
Copy and paste as a new layer and place on the left hand side of the frame.
Add a drop shadow.
Open element 19 and resize by 50% 2x.
Copy and paste as a new layer and move to the top left.
Drag under the light.
Image rotate to the left 22 degrees.
Add a drop shadow.
Duplicate and flip horizontal.
Move over to the right hand side and drag behind your tube.
Add your name and copyright information crop and save.
Lets move onto the banner:
Open a new blank canvas 650x225
Open paper 5 and copy and paste as a new layer.
Move up so that the more purple on the bottom is in your tag area.
Crop your tag to get rid of the excess paper.
Apply the Xero Fritillary filter like you did on your tag before.
Open the closeup of your tube and resize by 80% 2x.
Copy and paste as a new layer and move to the far right of your tag.
Duplicate and on the top copy adjust blur gaussian blur of 10.00.
Lower the opacity of this layer to 60.
Add a drop shadow to the bottom layer.
Open element 22 and resize by 50% 2x.
Copy and paste as a new layer into the bottom left corner.
Add a drop shadow.
Crop your tag to clear excess.
Open element 6 and resize by 75%.
Copy and paste as a new layer and drag to just above your paper layer.
Position at the bottom of the tag.
Open element 46 and copy and paste as a new layer.
Drag to just above your paper layer.
Position how you want in the tag area.
Add a border of 4 using color # 662c6a
Then add another border of 8 in some off the wall color.
Add another border of 4 using the color #662c6a
Using your magic wand select the off the wall color border.
Add a new raster layer.
Open paper 2 and copy and paste into selection.
Selections select none.
Add your name and copyright information.
Lets begin the Avatar:
Open a new blank canvas of 160x160
Open paper 5 and copy and paste as a new layer and drag to where the purple is again in the tag area.
Apply the Xero Fritillary filter using the same settings.
Open your tube and resize by 75% 2x.
Copy and paste as a new layer and move to the far right.
Duplicate and on the top copy adjust blur gaussian blur of 10.00.
Lower the opacity of this layer to 60.
Add a drop shadow to the bottom layer.
Open element 19 and resize by 50% 3x.
Copy and paste as a new layer and image rotate to the left 22 degrees.
Move to the top left corner and drag to just above your paper layer.
Duplicate and flip horizontal.
Move down just a bit.
Add a border of 2 using the color #662c6a.
Add a border of 5 using an off the wall color.
Add another border of 2 using color 662c6a.
Using your magic wand select the off the wall color.
Add a new raster layer.
Open paper 2 and copy and paste into selection.
Selections select none.
Add your name or initial.
Add your copyright information.
You are done!!!
Phewwwww!!!!!!








No comments:

Post a Comment